![]() ![]() If the Preset Switch is pressed, DISABLED will be displayed momentarily. If there is more than 10 PSI pressure on the pump, the RPM Preset is disabled. PRESET MODE - Pressing the PRESET switch in either mode will control the engine to attain the preset RPM or pump pressure programmed in governor memory. When switching to PRESSURE, the pressure set point is whatever pressure is on the transducer at the change. The message center will indicate “PRESSURE†or “THROTTLE†as appropriate once the mode change has been made. ![]() Switching between modes by pressing the mode switch will change the governor from RPM to Pressure mode without a significant change in engine speed or pump pressure. When controlling in this manner, the display will show CTRL DEC or CTRL INC. The governor maintains pump pressure by controlling engine RPM in response to a signal from the pressure transducer mounted on the pump. The display will indicate “INCREASE†or “DECREASE†as appropriate. The governor will attempt to maintain the last pressure achieved with these switches. Pump pressure is set by using the INCrease and DECrease switches. PRESSURE MODE - When the unit is operating in the Pressure mode, the display will show “PRESSURE†and the PRESSURE LED will be illuminated. Note: the governor will not attempt to regulate pressure in this mode, only limit the differential pressure to 50 psi from the pressure present when the last switch was pressed. The governor may reduce engine rpm to achieve this and the message psi limit will be displayed in the message center. Note: if while operating in rpm mode the pressure increases more than 50 psi from the pressure logged at the last switch press, the governor will limit the pressure increase to no more than a 50 psi differential. ![]() The engine will maintain an RPM appropriate for the throttle signal being sent. The governor will maintain the last output signal attained with these switches. Engine speed is controlled by the INCrease and DECrease switches and the display will indicate “INCREASE†or “DECREASE†as appropriate when these switches are depressed. RPM MODE - When the unit is in RPM mode, the display will read “THROTTLE†and the green RPM LED will be illuminated. If the pump is engaged and the OK to Pump LED is illuminated, PRESSURE will be the first mode selected otherwise Throttle will be the first mode. POWER ON - When the unit is first powered up, the display will show and the engine will remain at idle until the mode switch is pressed to select the desired operating mode, PRESSURE or RPM. Your explanation is almost word for word to what we were told and shown. We just had our delivery class last Saturday on our new engine. I believe Class 1's website (Hale IDEX) has a video clip showing how their electronic governor works. When drafting, you need to start in PSI mode until water is established, because if you start in PSI mode, the safety feature in the governor will sense no water pressure and return the engine to idle. You should always operate in PSI mode on a fireground with handlines deployed. This allows the pump pressure to remain at the set pressure when lines are opened/shut during operations. PSI mode uses a pressure transducer on the discharge side of the pump to tell the electronics how much RPM is needed to maintain a set pump pressure, using the cruise control segment of the engine's ECU. Not what you want selected for safety reasons when pumping handlines. If you are in pump, it will increase/decrease your discharge pressure, but will not compensate for lines being opened/closed. Trophy room where the player sees various memorabilia collected during renovation missions.In a nutshell: RPM mode is an electronic throttle only, which regulates the engine speed.Buy cosmetic items you can place around your office.Earn money on your renovation jobs and use it to expand your own base of operations – each room unlocked will add some perks and some of the rooms come with a side mission.Buy new tools and upgrade the equipment you already own. ![]() Two game modes: Campaign with a predefined number of levels and storyline.Collect trophies and mementoes during your renovation missions and display them proudly in a special room for everyone to see. Restore gyms, courts, pools and pitches to their former glory, upgrade your tools and expand your headquarters. How do you save your beloved team’s court from being torn down by a real estate developer? You do what you do best – renovate dilapidated sports facilities to collect the money you need to help out. Restore the glory of sports in a relaxing renovator sim, made by Goat Gamez, a studio founded by Movie Games and Robert Lewandowski! What happens when a sports game meets a house renovator? A game where you renovate old sports facilities! ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |